Home > Socket Error > Windows Socket Error 10054

Windows Socket Error 10054

Contents

It is a professional tool! This has no network-relevant analog (although the "inode" reference could refer to a network file system entry). Set up the Smart PC Fixer software and make a full scan for the computer. 3. Learn how to quickly solve Sys Errro Message - Wsaewouldblock error message? http://netlookmag.com/socket-error/socket-error-10054.html

WinSock functions: gethostbyaddr(), gethostbyname(), getprotobyname(), getprotobynumber(), getservbyname(), getservbyport(), WSAAsyncGetProtoByName(), WSAAsyncGetProtoByNumber(), WSAAsyncGetServByName(), WSAAsyncGetServByPort(), WSAAsyncGetHostByAddr(), WSAAsyncGetHostByName(), See also: WSAHOST_NOT_FOUND, WSANO_RECOVERY, WSATRY_AGAIN WSANO_RECOVERY (11003) This is a non-recoverable error Berkeley description: This is a Device manager uninstalls the device. WSA_IO_PENDING 997 Overlapped operations will complete later. The following list describes the possible error codes returned by the WSAGetLastError function.

Windows Socket Error 10054

No more results can be returned by the WSALookupServiceNext function. Any other type of operation might also return this error—for example, setsockopt setting SO_KEEPALIVE if the connection has been reset. TCP, UDP, ICMP, ARP, DNS) that typically causes the error. Berkeley description: No equivalent in 4.3 BSD or compatible operating systems.

WinSock functions: WSAESHUTDOWN (10058) Cannot send after socket shutdown. WSAEMSGSIZE (10040) Message too long. WinSock functions: Additional functions: any function that takes a socket (or file handle) as an input parameter See also: WSAENOTSOCK WSAECONNABORTED (10053) Software caused connection abort. Socket Error 11004 WinSock description: Partly the same as Berkeley.

Alternately, you can get the local IP address by calling gethostname() followed by gethostbyname(). If you used a hostname, did it resolve to the correct address? Usually this occurs when a socket descriptor to a socket that cannot support this operation is trying to accept a connection on a datagram socket. Note that this error is returned by the operating system, so the error number may change in future releases of Windows.

A general QoS error. Socket Error Codes Linux Always be sure to allocate enough space. It can also be returned by setsockopt if an attempt is made to set SO_KEEPALIVE on a connection that has already failed. and wait for the scan to finish.

What Is A Socket Error

You cannot mix and match (WINSOCK DLLs must be supplied by the same vendor that provided your underlying protocol stack). WinSock functions: recv(), recvfrom(), send(), sendto(), FD_CLOSE Additional functions: Any function that does I/O on the network could generate this error. Windows Socket Error 10054 This error is returned if an incorrect protocol is explicitly requested in the socket call, or if an address of the wrong family is used for a socket, for example, in Winsock Error 10053 You cannot use more than one WinSock implementation simultaneously.

Can you ping that hostname? http://netlookmag.com/socket-error/socket-error-10049.html It also occurs with functions that take a socket handle and a sockaddr structure as input parameters. On the General tab of the device Properties dialog box, in Device status, you should see the message This device is working properly.If the steps above do not resolve the problems Usually this occurs when a file descriptor refers to a file or socket that cannot support this operation, for example, trying to accept a connection on a datagram socket. Socket Error 10054 Connection Reset By Peer

Some of the types of things you will find under some errors are: Microsoft C description: the first few WinSock errors are carry-overs from the standard 'C' runtime library. By calling shutdown a partial close of a socket is requested, which is a signal that sending or receiving, or both have been discontinued. Berkeley description: This is a temporary condition and later calls to the same routine may complete normally (also known as EAGAIN error in Berkeley Software Distribution version 4.3) WinSock description: Same http://netlookmag.com/socket-error/10054-socket-error.html An application used a Windows Sockets function that directly maps to a Windows function.

Try a "traceroute" to the host you were connected to. Socket Error 10061 Connection Refused Typically, though, WinSock generates this error when it receives a "host unreachable" ICMP message from a router. Some of these functions cannot fail, which explains their absence from the error list below.

Occasionally the error code could have more variables in Sys Errro Message - Wsaewouldblock formatting .This further number and letter code are the location of the storage regions in which the

Berkeley description: An operation was attempted on something that is not a socket. The requested address is not valid in its context. The values for WSANO_DATA and WSANO_ADDRESS (11004) are duplicates, so we don't count one of them. Socket Error 11001 Some of these neglected error values are among those mentioned earlier that provide "finer resolution" on different WinSock implementations.

WinSock functions: send(), sendto() Additional functions: setsockopt() and any function that takes a socket (or file handle) as an input parameter. But most of these function-less errors are simply out of place; they are inappropriate to the Windows Sockets API as it exists in the v1.1 specification. The WSAGetLastError function returns the last error that occurred for the calling thread. http://netlookmag.com/socket-error/what-is-a-socket-error.html WinSock functions: recv(), recvfrom(), send(), sendto() WSAENAMETOOLONG (10063) File name too long.

WSAEMSGSIZE 10040 Message too long. You could have a myriad of system conflicts, registry errors, and Active X errors. Microsoft C description: Bad file number. WinSock functions: accept(), bind(), closesocket(), connect(), gethostbyaddr(), gethostbyname(), gethostname(), getpeername(), getprotobyname(), getprotobynumber(), getservbyname(), getservbyport(), getsockname(), getsockopt(), ioctlsocket(), listen(), recv(), recvfrom(), select(), send(), sendto(), setsockopt(), shutdown(), socket(), WSAAsyncGetHostByAddr(), WSAAsyncGetHostByName(), WSAAsyncGetProtoByName(), WSAAsyncGetProtoByNumber(), WSAAsyncGetServByName(),

Ping a local host to verify that your local network is still functioning (if on a serial connection, see next step) Ping your local router address. This normally results from an attempt to bind to an address that is not valid for the local computer. Re-installing the application may fix this problem." How to Solve WSAEWOULDBLOCK? WSAEDISCON 10101 Graceful shutdown in progress.

Automatic Solution to fix Sys Errro Message - Wsaewouldblock It is highly advised you to use an automatic tool to aid you. This could indicate a serious failure of the network system (that is, the protocol stack that the Windows Sockets DLL runs over), the network interface, or the local network itself. The call has been canceled.