Home > Symantec Error > Symantec Error Loading Operating System

Symantec Error Loading Operating System

However, after the pre-OS authentication, it will begin loading the OS from the address specified in the original MBR so it is important that the original MBR is accurate and not Also, confirm that the recovery points are not stored on the local drive selected.5. Make sure the correct internal hard drive to be wiped is selected and not any external drives where recovery points are stored. After restore. have a peek at this web-site

Try these resources. Run recover SEE has discovered an unsupported storage controller,contact SEE Tech Support. Delete the partitions for any additional internal drives using steps 4 and 5 above. I did not write down everything I did the first time because I expected everything to go without a hitch.

Don't have a SymAccount? Your gut feeling nailed it. Don't have a SymAccount? Thank You!

Boot from the CD 1. Please use the steps below to resolve the issue. Create a SymAccount now!' Error when booting after restoring a computer using the Symantec Recovery Disk: Error loading operating system TECH74089 January 11th, 2010 http://www.symantec.com/docs/TECH74089 Support / Error when booting after Calculate how much space new space you want to assign to System partition and this space must be removed (made unallocated) from the largest partition which is the Data partition.

Checkmark and restore only the apps partition. Things I tried: boot into the recovery console from the install disk (actually I uses a slipstream disk of XP with SP3) tried fixmbr, then fixboot, then both Confirmed the system Grover's New Revised Guides 4. 2014 Cleanup 2015 Cleanup 5.Attachments/How7.TI 2015 FAQ. 2. If the drive is not to be resized, leave the predefined partition alone that is the original drive size. 19.

Translated Content This is machine translated content Login to Subscribe Please login to set up your subscription. On the same screen, choose the following options and deselect everything else:"Set drive active (for booting OS)""Partition type: Primary""Restore MBR"If the drive is to be resized from its original size, also I needed to resize my system partition (effectively the steps were shrink data partition, shift apps partition, expand system partition) and was thrilled that I had my handy dandy DD to Top Login to post comments Sun, 2011-12-18 17:49 #4 GroverH Offline Legend Joined: 2009-08-15 Posts: 11298 I assume you can always get back to where you are right now and I

Should there be a need, you could restore it later by restoring only the Track0/mbr which would take you to the page where the target disk is selected and there you Make sure everything else is unchecked:"Partition type: Primary""Restore original disk signature"If the drive is to be resized from its original size, also select "Resize restored drive" and specify a drive size Registration E-mail: * Password: * Useful Links How to get Support? So far I have completed the following Acronis True Image Home 2011 Boot Disk Here is an accounting of my steps from the aspect of the menu system: From the

Using 2014 6.Help 2016 2015 2014 2013 8.Stop Scan for Backups 8A.ATIH Video's 3.Create new disks-Guides.9.Register/Downloads 10.Mustang's New Guides11.Les Seiler's Backup Video

Top Login to post comments Sun, 2011-12-18 04:32 http://netlookmag.com/symantec-error/symantec-error-0x80070102.html The Encrypt Whole Disk (Partition) work area displays, and you see a listing of the disks on your system that can be protected by PGP Whole Disk Encryption. If you know how to use Disk Part, this is an option. Once that restore finishes, follow steps 15 through 21 above to restore each data drive.

Wipe the first track of any additional internal drives. 12. In any case, thank you very much for your help. I don't know how to avoid this problem the next time I need to do some disk maintenance. Source Data Backup and Disaster Recovery Software.All Rights Reserved.

Supported Products A-Z Get support for your product, with downloads, knowledge base articles, documentation, and more. In order to clean the hard drive and run the restore again, the following procedure should be followed:1. At this point, I would not do a restore of it unless there is software recognition issues.

At the initial Black Screen: “Starting Symantec Endpoint Encryption…” -> Most likely a Hardware Compatibility issue. 2.

On the Data partition, create the desired free space (to be added to system partition) before the partition. Or, you an achieve the same effect from the TI boot CD using the add disk option to delete the partitions. This is because it can corrupt the volume files which are the protected OS files in which the Pre-OS is located. Delete the contents of the system disk. 1.

I was quite confident that I was presented that option (and I selected it) when I did the first restore, but not seeing it this time makes me question if I Once all of the drive restores are finished, remove the Symantec Recovery Disk and reboot the computer Legacy ID 330526 Terms of use for this information are found in Legal Notices. Submit a False Positive Report a suspected erroneous detection (false positive).

Information for: Enterprise Small Business Consumer (Norton) Partners Our Offerings: Products Products A-Z Services Solutions Connect with us: Support have a peek here The Free space before should be 0 and the free space after should be the intended size of the data partition.

B. From the menu presented choose "First Track Operations"9. Using 2014 6.Help 2016 2015 2014 2013 8.Stop Scan for Backups 8A.ATIH Video's 3.Create new disks-Guides.9.Register/Downloads 10.Mustang's New Guides11.Les Seiler's Backup Video

Top Login to post comments © 2000–2016 Acronis The resize finished successfully, but the subsequent reboot failed with the error, "Error loading operating system".

A. Create a SymAccount now!' Troubleshooting Pre-OS boot issues with Symantec Endpoint Encryption. In the partition list there will be a partition which is the size of the original drive. Products Products Home Threat Protection Advanced Threat Protection Endpoint Protection Endpoint Protection Cloud IT Management Suite Email Security.cloud Data Center Security Blue Coat Products Information Protection Data Loss Prevention Encryption VIP

But, thanks, and all that.

Top Login to post comments Mon, 2011-12-19 02:02 #8 GroverH Offline Legend Joined: 2009-08-15 Posts: 11298 The Recover Disk signature would have been on the Submit a Threat Submit a suspected infected fileto Symantec. Error An error such as the following may appear: The EAFS volumes contain errors run recover E+ Err 5! So I bought a second drive and I bought an acronis bundle with both DD and TI so I would never be in that situation again.

Submit a False Positive Report a suspected erroneous detection (false positive).

Information for: Enterprise Small Business Consumer (Norton) Partners Our Offerings: Products Products A-Z Services Solutions Connect with us: Support So I'm hoping that someone has some insight into how I might fix mine boxen, or at the very least, why did this happen?

Top Login to post comments Sun, This error is typically caused by either restore settings that were not properly selected or by pre-existing partitions on the disk. Running “chkdsk /f /R” prior to installing SEE will check for and flag bad blocks.

This option is only need if you have software which is using the disk id for recognition of a valid install. If you are not familiar with the procedures above, you can get a general idea by reviewing m index item 3-BB. Checkmark and restore the data partition. Reconnect any external drives which contain the recovery points13.