Email check failed, please try again Sorry, your blog cannot share posts by email. The "domain" firewall should be turned off. Try these resources. Windows 7 SP1 and Windows 7. have a peek at this web-site
Manual application of GHREGUPD.REG via GHConfig32.exe is broken, too. Not a network problem. This simple tweak shaves heaps of time off of WinPE (also Linux) automation boot times. Once I hit ^Break, I got the c:\ prompt, but all commands seem to get "bad command or filename" and rebooting only returns to it. Well, that thrill didn't last long, because last week the seven-year-old Server 2003 machine that had been hosting our Ghostcast died. I have put up a new machine in its place,
The built-in admin account should be enabled and have a password. To solve the problem, see Is the "Sharing and security model for local accounts" policy set to Guest Only?. It does not matter if DOS or WinPE is used the GHO files boot from DVDs or CDs.
And \images is just the conventional location where we're storing image files. When you have created your imaging job, enter the properties of the imaging task and replace %IMAGE_FILENAME% to @MCSESSION with SESSION being the name of the GhostCast session we will create Now you will see once they have booted up and started the modified imaging job that they will be at the Symantec Ghost screen waiting for a GhostCast session to start. Send to Email Address Your Name Your Email Address Cancel Post was not sent - check your email addresses!
When you're done with re-imaging, take care of all the things you normally would after a fresh Windows install: Windows Updates, antivirus, etc. After about 10 seconds you will get a message saying that it Successfully registered Backup Exec with LiveUpdate and set the mode to OptOut. To solve this problem, see Is the Microsoft Windows Firewall blocking port 445?. When manually testing the application of the GHREGUPD.REG configuration I used the X:\Ghost folder to contain the file. I used the following commands to apply the GHREGUPD.REG configuration file on my
Thank you for your feedback! Port 445 is blocked If the Microsoft Windows Firewall is not configured to allow File and Printer Sharing (port 445), authentication will fail. Supported Products A-Z Get support for your product, with downloads, knowledge base articles, documentation, and more. When the task finishes, go to the target machine and you will see a command prompt that keeps pinging the Ghost server.
This is the first time we have had a T3600 with the onboard controller, previously we had models with an add in RAID card that worked fine once i added the Check This Out Once it restarts, return to the Backup Exec Services Manager and click on Start All Services to start them all up again. discussion comment 15 Jan 2013 mteehan commented on: Error opening Service Manager Like I said, I can push to XP machines so our firewall is not the issue. Often, Symantec prevents you from having access to enabling/disabling Windows Firewall.
Once the task seems to be going smoothly, you can go over to the target computer and see the progress there (if you want to burn some calories). When you are there run the following command: BeUpdateOps -Addbe -OptOut This will cause backup Exec to register itself with LiveUpdate . Theme is Kirumo Home Contact Me
However if I repeat the process only this time select my USB flash drive as the destination Ghost creates a GHO file but it will not boot. The problem I am having is I successfully create an image using sysprep and when I go to deploy this image to a computer that the image was not created from Executing the clone task On Ghost Console, go to Tasks.
If I select my DVD/CD burner as the destination and back my hard drive up to DVDs or CDs Ghost creates GHO files that boot starting the Ghost Boot Wizard. I am going to have to image over 80 computers next month and only have an 8 port KVM, I need to get this as automated as possible. Create a SymAccount now!' Error: "Login to [computer] failed. Submit a Threat Submit a suspected infected fileto Symantec.
Solutions for Windows Note: The Symantec Diagnostic Tool (SymDiag) can automatically detect many of the common problems that cause this error message to appear, and guide you to specific information on Firstly, open up the Services control applet and Stop the Altiris PXE MTFTP Server service. This last step is very important. have a peek here Create a SymAccount now!' Remote Client Install Error "Failed to install: \\XC2098 (50): Service: Error opening Service Manager" TECH199522 October 30th, 2013 http://www.symantec.com/docs/TECH199522 Support / Remote Client Install Error "Failed to
Luckily the solution is simple. Right-click Network Security: LAN Manager authentication level, and click Properties. Check the username and password and try again." TECH91715 October 29th, 2016 http://www.symantec.com/docs/TECH91715 Support / Error: "Login to [computer] failed. To do this I select Disk then To Image in Boot Wizard.
It fails with error 20. Our generic domain admin account name is the same as our local admin account but I tried my personal admin account as well which is different and that didn't work. The following is based on our Altiris setup, with it installed on D drive and me creating a folder under PXE for OpenTFTP and pasting the OpenTFTP executable and Settings file Can anyone help? 8164541 13575833040 0 01/07/13--10:05: Black screen, blinking cursor after deploying ghost image Contact us about this article I need a solution We recently got some HP
It is important that this file path should not include any numbers*. Creating an image space The first thing you have to do, before actually starting to clone an image off of a computer, is to create a space into which the cloned Configuration push from GSS console fails to revert machines from static to DHCP address. Client machines are various hardware, but all run Ghost32 in either WinPE 3.0 or 4.0.
Now open up the SQL Server Configuration Manager and restart the instance of SQL Server hosting your Backup Exec database. discussion comment 15 Jan 2013 mteehan commented on: Error opening Service Manager UAC and Windows Firewall are always disabled on all of our machines. Check the username and password and try again." Cause There are a number of different problems that can cause the logon attempt to fail. Personal Open source Business Explore Sign up Sign in Pricing Blog Support Search GitHub This repository Watch 2 Star 0 Fork 0 Duke-Biology-IT/ghost-doc Code Issues 0 Pull requests 0 Projects
For Target Machine Group / Machine, browse and choose the right computer(s). While the run itself successfully contacted the server, I find myself unable to get out of the app and unable to find any documentation on how to do so. Education Services Maximize your product competency and validate technical knowledge to gain the most benefit from your IT investments.