Turn the printer on. Respond to this 0 I found this guide on HP's website that may be useful to you.The 86.01 is a carriage movement failure. Superimposed is a lot of ink splatter. the carriage will stop at ramdon places during printing.Normally,just by oiling as mentioned will resolved this common fault,but not this time..... http://netlookmag.com/system-error/operating-system-error-3-the-system-cannot-find-the-path.html
HP Support Advanced 33,868 views 7:24 Designjet T610, T1100, Z2100, Z3200 Carriage Belt Replacement Tutorial - Duration: 49:42. Slide the carriage manually back and forth several times to evenly spread the lubrication across the entire carriage rail. open window2. HP Printer Support 530,881 views 2:37 DesignJet 500 carriage and belt removal - Duration: 10:27.
by dlstoehner on Jun 19, 2014 at 8:07am Add comment Please sign in to comment Please sign in to comment HP DeskJet 500 Buy discount ink Buy this printer More HP If functionality is verified, no additional parts should be replaced. switch power off3.
HP Printer Support 24,000 views 5:03 HP DESIGNJET 130 PRINTER - Duration: 3:55. The issue happens on the cutter side, not the service station side. If so something was not done right and the plotter is sensing that door not being shut properly. I moved the carriage back and forth many times for the lube to work into the bushings.
Is the WD40 an OK lube? Reply 0 0 Resolutiongbcom Honor Student Posts: 2 Member Since: 07-20-2016 Message 6 of 6 (3,257 Views) Report Inappropriate Content Re: [Solved] HP DesignJet 500 Error 86:01 when trying to trim Rating is available when the video has been rented. switch power on5.
lithus87 31,797 views 6:33 Unboxing and Setting Up the HP Deskjet 2540 All-in-One Printer - Duration: 8:46. NOTE: When replacing the trailing cable, use the stiffener that ships with the 1000 series trailing cable. Loading... Loading...
Solution 3: Verify the Service Station Take out the service station and make sure it run through its full range of motion by rotating the motor spindle. Have the customer send a file from the computer and make certain that the file prints correctly. If even after this, the carriage is STILL NOT able to come out, contact us for technical support.4. French Site L'imprimante en question Friends Archaeology news Labels Brother (7) Brother DCP (6) Brother HL (1) Brother MFC (7) Cano IR (1) Cano S (1) canon (29) Canon BJC (2)
Lubricated the drive rod Removed and cleaned the cutter head. Its seems to move ok, but I don’t know how much resistance should be when sliding this part. navigate here The plotter got about 90+% complete printing the test plot on the gloss paper(image attached). The plotter did not cut the paper. Then it showed Error 86:01. Carriage returns to the service bay and then backs out to left. If the percentage is close to 100%, then lubricate the Slider Rod (there is probably too much friction in the Slider Rod).
Remove the stiffener from the box and install on top of the HP Designjet 500/800 trailing cable with the concave side down. WARNING: Be careful when working around the Encoder strip, as the edges are very sharp and can cause injury. Turn the printer on and attempt to verify functionality.
Contact our Support Team on 0115 772 2045 or email [email protected] for help diagnosing your fault.Bookmark the permalink. Turns out it has lots of little black lines running across it vertically. Specifically, it is normal to hear a slight clicking noise when the carriage moves under the left or the right-hand covers. The service bay performs some type of cycle.
Loading... Also what happens if you turn the cutter off. Check for the rods, that holds the cleaners, to be not popped out. http://netlookmag.com/system-error/flexnet-licensing-error-96-7-system-error-11001-comm-error.html by dmzcompute on Feb 17, 2014 at 4:43pm Add comment Please sign in to comment 0 I am getting this same error - now.
so now that i have the carriage working LOL the black ink even tho its in there is saying missing ink... If that works then check on the window. Try to restart a couple of times. Enter service mode.
I lubed the carriage rail with the only lubricant that I had - WD40.